Showing results: 91 - 105 of 131 items found.
-
SKU-055-0X -
Amfeltec Corp.
The Flexible MiniPCI Express Riser (Riser) was designed to extend the MiniPCI Express bus. The Riser includes a MiniPCI Express adapter board (downstream), MiniPCI Express host board and a 12” PCI Express flat cable.The MiniPCI Express host board connects to the motherboard MiniPCI Express connector.
-
APCI-7300-3 -
TEAM SOLUTIONS, INC.
*PCI interface to the 32-bit data bus. *Asynchronous communication adapter, 1-port serial interface*1 socket for SI modules*Modular structure through SI modules*Configurable as: RS232, RS422, RS485, with or without isolation, or 20 mA Current Loop (active, passive) with isolation*Addressing through software
-
60-982-001 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
60-982-002 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
PMC-MC-X2 -
Dynamic Engineering
The PMC-MC-X2 adapter / carrier converter card provides the ability to install up to 2 (two) PMC cards into a small enclosure. The PMC-MC-X2 has one PMC card slot mounted front and rear to create a compact arrangement with 2 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
PMC-MC-X4 -
Dynamic Engineering
The PMC-MC-X4 adapter / carrier converter card provides the ability to install up to 4 (four) PMC cards into a small enclosure. The PMC-MC-X4 has two PMC card slots mounted front and rear to create a compact arrangement with 4 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
PCI2cPCI -
Dynamic Engineering
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
PCI2cPCI-32 -
Dynamic Engineering
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
PCI3IP -
Dynamic Engineering
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
PCChost 1420 -
Sycard Technology
Based on Texas Instruments' PCI1420 CardBus host adapter chip, the PCChost 1420 PCI-to-CardBus bridge provides the engineer with a platform to evaluate a high performance ACPI compliant CardBus bridge device. Contained on a single Peripheral Component Interconnect (PCI) bus card, the PCChost 1420 is compatible with a wide variety of PC and non-PC PCI hosts.
-
Model JI-300 -
Jupiter Instruments
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
SKU-050-0X -
Amfeltec Corp.
The Flexible 32-bit PCI Riser (Riser) was designed to expand the 32-bit PCI bus into 2 32-bit PCI buses. The Riser includes a PCI adapter (downstream), 32-bit PCI host board and PCI Express Flat cable.The PCI adapter has 2 32-bit PCI slots for plugging in two 32-bit PCI add-in boards. The PCI host board connects to the motherboard PCI connector. The PCI Express Flat cable (12 inches) is used for connecting the host board with the PCI backplane, and it provides a flexible connection between the 32-bit PCI add-in boards and the motherboard.
-
cPCI2PMC -
Dynamic Engineering
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
AS519 -
6TL Engineering
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
0149-SX -
Strobe Data Inc.
Same speed Windows/NT Kestrel Co-Processor for equivalent system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.